Reverse Titanium Axles V2 – Adjustable Trackwidth System

Upgrade your front end with our V2 Reverse Axles, now machined from titanium for improved durability and long-lasting performance. These axles allow you to fine-tune your front offset by 1mm, adjustable in 0.5mm increments using the included M3 x 0.5mm axle shims.

Compatibility

• Reflex Racing RX28

• GL Racing chassis

• Atomic chassis

Why Reverse Thread?

By reversing the thread direction and using a screw instead of a nut, the axle system greatly reduces the chance of your front wheels snagging on RCP rails, especially when running low-offset wheels.

What’s Included

• 2× Titanium Reverse Axles (V2)

• 4× M3 x 0.5mm Copper Shims

• 2× M2 × 4mm Button Head Screws

Pro Tip

Depending on the wheels used, there may be a small amount of axial side-to-side play.
To eliminate this, you can lightly sand the outer axle surface to reduce the width slightly.

-1x M2x6 BH Screw (use M2x6 BH Screw plus M2 gold washer on top of top spring when installing 2 weights).

-1x M2 Gold Washer

-2x Black MD Spring (Soft)

-2x Silver MD Spring (Medium)

This is a set of Full Ceramic Bearings for you 1/28 scale Pan Car.  Full Ceramic Bearings offer many benefits as outlined below:

1. Reduced Friction: They provide lower rolling resistance, which can improve the car's speed and overall efficiency.
   
2. Enhanced Durability: The wear-resistant nature of ceramic bearings means they can last longer under the high stress.
3. Lightweight: While not a lot, a full set of ceramics drops about 0.5g off your car.
   
4. Reduced Maintenance (somewhat): The low friction and wear properties eliminate the need for oil or grease. However, as our bearings have no races, they can allow more debris and tire dust to enter the bearings.
   
5. Corrosion Resistance: As they are not metallic, your bearings can be washed with something like dish soap and water.

Great way to add weight to your RX28 or FX28 on the lowest part of the chassis.  Install under the battery for additional stability.

Much welcome addition to the Reflex Racing stable, the all new bearing tool is tailor-made for small scale needs.  Compatible with 2.0/3.0/4.0mm ID bearings.  

RX601G

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601W

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX601Y

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX411

4x7x2 bearings (2)

RX601B

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

RX28-045G2 (Black: Medium; Kit w/ 2 Upper & 2 Lower Arms, 4x Balls & 4x Screws)

• (1) Medium center spring (Black) for RX28

T Bar for Reflex F1 Chassis

AC-131-R

AC-071-R

RX28-017

REFLEX RACING RX28 SOFT FRONT SPRINGS (WHITE SILVER)