RRE015

All New from Reflex Racing is our 400mah LiHv battery. This battery offers longer runtime, lower IR and overall better performance for longer races vs the 340mah pack all while only weighing an extra 2g. This battery is slightly bigger so, it will only fit your RX28 when using the 24mm battery conversion kits or the 102mm WB Chassis. This battery will fit most AWDs car in the market as well as other cars that are capable of fitting a 24mm wide battery.

Why hardcase? Well, hardcase batteries have numerous benefits. Due to its design, a hardcase cuts down on connection points, uses more efficient plugs and thicker wire. These 3 elements drop the internal resistance of the entire circuit leading to better overall current flow, less heat loss and more performance. Couple that with the additional voltage capacity (these are safe to charge to 8.6v!) and the result is a sure fire winner.

The Benefit of having a battery that sits solidly in place on the chassis offers a handling advantage as there are no plugs and wires dangling inside the car. (Just think, we use 0.9g mass damper weights to stability our cars. Plugs and wires often represent more than this weight and they are jumping up and down inside the body of the car when using a soft case pack. ). The result is a car that behaves more smoothly. Additionally, hard case batteries simply wire better. In categories like Pan Car, where wiring is a bit tricky to fit under the low slung bodies, the hard case bullet to battery system opens up a tremendous amount of space under the body. 

Lastly, hard case batteries are also safer and tougher. Wires don't break at the exit of the shrink, so shorts are minimized and, the hard case also protects the cells from damage better, as well as isolates them from possible punctures or shorts caused by the chassis or impacts.

We recommend to charge the batteries at 1.0A

Dimensions:

44.5x24x12.5mm

Weight:  

19g

Includes:

1 battery pack

2 gold bullet plugs

You Can use Cable no:  RRE013 to charge. 

RRE016

This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!

RX28-003

RX28A-34

The all new 102mm wheelbase conversion kit fits all your flat plate versions of the RX28 release to date. It is designed to allow you to mount 102mm bodies like the Mazda 787B on the car for a more versatile experience (Kiss front end needs slight clearance sanded around upper arm area). The chassis was designed with versatility and light weight in mind. You can now use a larger 24mm battery or move the battery on the chassis forward by 4mm to fine tune your weight bias through the included extra holes on the chassis and battery stop.

The kit includes:

-RX28 102mm Hardened Steel Plate Chassis with Light Weight Cuts

-4mm Shock Cap Extender post and 1mm shim

-Battery Stop Post and Screw

-Body Side Clips (Tested on Maxda 787B only so far)

RX607F125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RRE009-5

Made with tough PVC Sheathing, this ESC to receive link wire is more durable and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look!

This set comes with 5 sets of wires. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.

RX607R125G

Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.

Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.

These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.

***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.

RX28-045G2

Version 2 molded A-Arms for your RX28. This is the G2 arm sets with dedicated left and right arms.

This set includes:

-2 x Upper Arms (Black/Medium)

-2 x Lower Arms (Black/Medium)

-4 x 3.55 Aluminum Pivot Balls

-2 x M2x6mm Screws

-2 x M2x8mm Screws

-2 x M1.2x5mm self tapping screws

-2 x M1.2x4mm self tapping screws

RX602-30

All new from Reflex Racing is our brand new radial tires for RCP tracks. Through out testing in several spots across the USA we have found these tires to perform on par and often beyond the other offerings in the market. The feedback from both Pros and Joes is that these tires offer superior stability under rotation and great forward grip out of the corners.

The design of this tires was conceptualized so that the tire was not directional and instead of building a tread pattern on a slick, we actually cut into the slick to create a tread pattern. The result is a tread that flexes less for more stability under load and better exit traction. The compound was selected so that these tires still perform really well once the tread pattern has worn down well beyond being visible. In high traction conditions, this allows this tire to be used in smaller diameters, providing superior corner speed. Additionally we optimized the tire diameter for maximum corner speed and better rotation on the individual application. The 14mm tire is only 24.5mm in diameter, while the 11mm tire comes in at 25.25mm when mounted with super glue.

We recommend the 30 degree rear tires under most conditions. They work well in temps as low as 45 degrees (F) and perform well all the way into the 80's (F). If the grip is higher, simply cut the tire down smaller if you want a little more rotation in tight corners.

***Wheels are for picture only, they are not included***

RX532BL

The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.

The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.

RX605-45

All new from Reflex Racing is our brand new Low Profile slick tires for RCP tracks. These tires are made from a very tough and long lasting grippy rubber. They were developed to match the grip envelope of our 30 degree radials.

We recommend to mount the tires 1 of 2 ways:

For a less hassle, no truing method, mount on a Reflex Racing Speed Dish Wheel with a 22.6 plate. Let the tire break in over time. It is very long lasting, but the results are that the tire works after a couple of laps. If it is too aggressive in the middle of the corner, try removing some camber or running a softer front spring.

If you like to true your tires, mount them up on a truer and bring them down to 22.7-22.8mm and use with a 22.6 plate. After truing, the tires may be a little bit aggressive while they break in, so make sure you have some freshly skimmed 30 degree rear radials or you may have too much front bite. Since the material is very hard, we recommend running the tire truer where the tire and drum are spinning away from each other. With the PN Brand of truers, we find the most success running the truer in reverse and around 6v.

So when do you chose the 45 vs the 40? The 40 cuts a little bit harder, but it is smoother in the middle of the corner. Opposite is true for the 45. It really depends on what you are trying to do. If you want more middle and exit, use the 45. If you want smoother middle and exit, use the 40.

***Wheels are for picture only, they are not included***

RRE014-5

These custom made 2mm split plugs by Reflex Racing are designed to be tougher and have less IR than other plugs available in the market. These plugs are manufactured to our strict specification, in order to solder better and have tougher soldering connections going to your battery, since the wires we use in 1/28 can be a bit fragile. In our signature, attention to detail style, we made a ridge on the top of the plug to make it easier to pull on a surface without having to yank on the wire.

RX528

RX28A-33-HS

RX28-032

RX28-015

RX604-40

All new from Reflex Racing is our brand new Low Profile slick tires for RCP tracks. These tires are made from a very tough and long lasting grippy rubber. They were developed to match the grip envelope of our 30 degree radials.

We recommend to mount the tires 1 of 2 ways:

For a less hassle, no truing method, mount on a Reflex Racing Speed Dish Wheel with a 22.6 plate. Let the tire break in over time. It is very long lasting, but the results are that the tire works after a couple of laps. If it is too aggressive in the middle of the corner, try removing some camber or running a softer front spring.

If you like to true your tires, mount them up on a truer and bring them down to 22.7-22.8mm and use with a 22.6 plate. After truing, the tires may be a little bit aggressive while they break in, so make sure you have some freshly skimmed 30 degree rear radials or you may have too much front bite. Since the material is very hard, we recommend running the tire truer where the tire and drum are spinning away from each other. With the PN Brand of truers, we find the most success running the truer in reverse and around 6v.

So when do you chose the 45 vs the 40? The 40 cuts a little bit harder, but it is smoother in the middle of the corner. Opposite is true for the 45. It really depends on what you are trying to do. If you want more middle and exit, use the 45. If you want smoother middle and exit, use the 40.

***Wheels are for picture only, they are not included***

RX28A-19

These 0.3mm caster shims can be used in combination with a 0.2mm shim to reduce the slop in your front end. Due to tolerance, sometimes a 0.2 with a 0.3 allows for less movement on the upper arms. The difference in caster is negligible, but we recommend using the towards the back.