Gen 3 Specific springs.  Shorter and bigger bore.

This is a set of Full Ceramic Bearings for you 1/28 scale Pan Car.  Full Ceramic Bearings offer many benefits as outlined below:

1. Reduced Friction: They provide lower rolling resistance, which can improve the car's speed and overall efficiency.
   
2. Enhanced Durability: The wear-resistant nature of ceramic bearings means they can last longer under the high stress.
3. Lightweight: While not a lot, a full set of ceramics drops about 0.5g off your car.
   
4. Reduced Maintenance (somewhat): The low friction and wear properties eliminate the need for oil or grease. However, as our bearings have no races, they can allow more debris and tire dust to enter the bearings.
   
5. Corrosion Resistance: As they are not metallic, your bearings can be washed with something like dish soap and water.

Linear springs are smoother in response than the standard springs. They are wound from smaller diameter wire and have less coils. This allows for the spring to have a more linear response through the suspension stroke. The front end tends to have a more constant response instead of getting more aggressive as the car rolls deeper; which is the case with the standard type springs. The Green Springs are similar in rate to the Kit Gold Springs (RX28A-12).

Reflex Racing Medium Front Springs for 1/28 scale

Great way to add weight to your RX28 or FX28 on the lowest part of the chassis.  Install under the battery for additional stability.

Gen 3 springs.  They are shorter than previous side springs, but are compatible across platforms.

Reverse Titanium Axles V2 – Adjustable Trackwidth System

Upgrade your front end with our V2 Reverse Axles, now machined from titanium for improved durability and long-lasting performance. These axles allow you to fine-tune your front offset by 1mm, adjustable in 0.5mm increments using the included M3 x 0.5mm axle shims.

Compatibility

• Reflex Racing RX28

• GL Racing chassis

• Atomic chassis

Why Reverse Thread?

By reversing the thread direction and using a screw instead of a nut, the axle system greatly reduces the chance of your front wheels snagging on RCP rails, especially when running low-offset wheels.

What’s Included

• 2× Titanium Reverse Axles (V2)

• 4× M3 x 0.5mm Copper Shims

• 2× M2 × 4mm Button Head Screws

Pro Tip

Depending on the wheels used, there may be a small amount of axial side-to-side play.
To eliminate this, you can lightly sand the outer axle surface to reduce the width slightly.

RX600R0Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX28A-39

All New RX28 Steel Chassis for your RX28G2 Plate Cars. This new chassis allow for fore and aft movement of 20mm wide batteries as well as making it compatible with our new 400mah batteries that are 24mm wide. This new chassis kit comes with lateral CF braces to locate the battery side to side, but also to stiffen the front to back structure of the car for more precise handling and higher corner speeds. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.

RX28-042

New G2 Ball Cups made for 2mm threads.

**Must be used with the RX28A-33 Shock, New G2 Turnbuckles and Side Dampers.

Use this cable with your Hobbywing Tunalyzer or Sky RC Motor Checker (may work with other testers that require larger scale to 1/28 scale small sensor plug).

RX600F0Y

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

Use this cable with your Hobbywing Tunalyzer or Sky RC Motor Checker (may work with other testers that require larger scale to 1/28 PN Racing Motor Sensor Plug).

RX600F0W

All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.

The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.

RX28SE-08

This all new chassis for your RX28SE Gen 2 changes the battery and shock mounting system slightly so that we can have more space to move the 340mah hardcase lipo fore and aft on the chassis, as well as allowing for our new 400mah LiHv battery to fit in the chassis in 98mm configuration. This chassis also sheds approximately 5-6g off of the chassis in higher areas ensuring that while the chassis gets lighter, the center of gravity does not suffer. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.

FX28 7075 T6 Aluminum Axle Carrier

RX511

RX28-030