RX601B

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

Gen 3 Specific springs.  Shorter and Smaller Bore.

RX28 Gen 3 Center Spring - Hard (Gold)

Much welcome addition to the Reflex Racing stable, the all new bearing tool is tailor-made for small scale needs.  Compatible with 2.0/3.0/4.0mm ID bearings.  

Replacement pod plate for your G3 D kit.  Has key holes for new pod, but will work with older versions.  

RX28 Gen 3 Motor Mount

• REFLEX RACING RX28 MEDIUM SOFT FRONT SPRINGS (BLACK)

Gen 3 Specific springs.  Shorter and Smaller Bore.

Reflex Racing RX28 Gen 3 Sway Bar - Medium (Silver)

RX28 Gen 3 Sway Bar - Hard (Gold)

REFLEX RACING RX28 SOFT FRONT SPRINGS (WHITE SILVER)

-1x M2x6 BH Screw (use M2x6 BH Screw plus M2 gold washer on top of top spring when installing 2 weights).

-1x M2 Gold Washer

-2x Black MD Spring (Soft)

-2x Silver MD Spring (Medium)

Gen 3 Specific springs.  Shorter and bigger bore.

New low CG tweak brace for your RX28SE G3.

RX601G

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

Optional CF Pod Plate for you SE Gen3 Kit.  This CF piece will shed about 3g of weight and it will increase rotation of your car.  Recommended for stock classes.

RX28A-45 Reflex Racing RX28 Hard-Coated Aluminum Top Shock Shaft 

Shed some weight from up top for an even lighter CG.  This shaft sheds 0.3g from your top shock, leaving behind a 1.41g top shock.  When combined with the new aluminum turnbuckles, part no:  RX28A-44, it will shed 0.85g up top