RX411

4x7x2 bearings (2)

Gen 3 Specific springs.  Shorter and bigger bore.

RX513V4

All New V4 Molded Spur and Covers.

Uses 2.381mm balls. This spur is compatible with most Mini-Z type ball differentials, but they do require a separate 4x7x2mm bearing.

RX601Y

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

• (1) Medium center spring (Black) for RX28

RX601W

Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car.

These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm.

How to use:

1. Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.)

2. Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way.

3. DRIVE!!!

It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.

Replacement Bands for your Reflex Racing Battery holder. 

Battery hold down band

Replacement pod plate for your G3 SE kit.  Has key holes for new pod, but will work with older versions.  

Replacement pod plate for your G3 D kit.  Has key holes for new pod, but will work with older versions.  

Gen 3 springs.  They are shorter than previous side springs, but are compatible across platforms.

RX28A Gen 3 Sway Bar - Soft (Black)

New low CG tweak brace for your RX28D G3.

RX28D Gen 3 – 1/28 Scale RC Car Chassis Kit

Redefine Performance. Precision. Possibility.

The RX28D Gen 3 is here to raise the bar for 1/28-scale RC racing. Built for drivers who demand speed, agility, and pinpoint control, this third-generation chassis is fully re-engineered to dominate the track with cutting-edge design and next-level adjustability.

🔧 Key Upgrades & Features

🚗 Front-End Enhancements:

• 1mm longer front arms for improved stability and smoother handling

• Integrated sway bar system for surgical cornering precision

• Adjustable caster (via 3 screws)

• Integrated front shock tower with shim-based ride height tuning

• Upper arm hinge pin height adjustment for custom camber gain and roll center

• Lightweight & durable plastic knuckles – new design, less weight, more strength

• Low-profile big bore shocks & springs – ultra-smooth, responsive handling

🏁 Rear-End Innovations:

• Lower CG Rear End for high-speed stability

• New motor mount – lowers motor by 0.8mm

• 3-screw damper mount – simplifies rear suspension servicing

• Tweak brace lowered by 1.25mm for improved response

• Shorter side springs + thinner perches

• Side dampers lowered by 3mm, now screw-mounted to motor mount

• Smaller center shock spring, collar, and perch

• Pinned rear motor pod plate – boosts durability and rear-end precision

🛠️ Ease of Maintenance:

• Standardized ball stud hardware used throughout

• Simplifies adjustments and part replacements

• Designed with trackside tuning in mind

📦 What's Included:

• RX28D Gen 3 Chassis Kit

• One set of wheels and tires (pre-mounted)

⚠️ Note: Electronics NOT included. See below for compatibility.

📏 Specifications:

• Wheelbase: 98mm

• Weight (RTR): 145g–170g (depending on body & electronics)

• Rear Track Width: 69mm–78mm

• Front Track Width: 72mm–75mm

🔌 Electronics Required (Not Included):

• Motor

• LiPo Battery

• ESC (Electronic Speed Controller)

• Receiver

• Servo

✅ Compatible Servos:

• Reflex Racing RRE007 (20T Spline) – Recommended

• AGFC A06CLS V1

• GL Racing Servo

• PN Anima

• Atomic Servo (tight fit, but compatible spline size)

🛠️ You Will Also Need:

• Body + Mounting Hardware

• Compatible electronics listed above

🚨 NOTE:

ELECTRONICS ARE NOT INCLUDED! This kit is designed for experienced builders who want a customizable, high-performance platform.

RX28-077 Gen 3 Upper Arm Turnbuckles

Gen 3 Specific springs.  Shorter and bigger bore.

All new shorter, big bore Shock Set for your Gen 3 RX28.  These shocks increase the damping ability of your front end and also lower the CG for faster cornering.  Please note that these have to be used with the newer front springs.

RX28SE Gen 3 – 1/28 Scale RC Chassis Kit

Precision. Versatility. Style.

Get ready to take your racing program to the next level with the RX28SE Gen 3 — the ultimate 1/28th-scale RC car chassis designed for enthusiasts who demand performance without compromise. This third-generation platform is built to dominate any surface with fine-tuned handling, premium materials, and unmatched tuning potential.

🔧 Key Features & Upgrades

🚗 Revamped Front-End:

• 1mm longer front arms for enhanced stability

• All-new sway bar system for sharper cornering response

• Adjustable caster (3-screw system)

• Integrated front shock tower with shim adjustment

• Adjustable upper arm hinge pin height for custom camber gain and roll center tuning

• Low-profile big bore shocks & springs for buttery-smooth handling and high grip

🏁 Rear-End Innovations:

• Lower CG Rear Design for increased agility

• New motor mount – lowers motor by 0.8mm

• 3-screw damper mount – simplifies rear suspension maintenance

• Tweak brace dropped by 1.25mm for enhanced cornering performance

• Shorter side springs & thinner perches

• Side dampers lowered by 3mm, now screw-mounted to motor mount

• Smaller center shock spring, collar, and perch

• Pinned Rear Motor Pod Plate – improved precision and durability

🛠️ Signature SE Upgrades:

• 24mm Steel Tub Chassis – Industry-leading rigidity, low CG, and durability

• Includes both Premium Ball Differential & Gear Differential

• Two sets of plastics included: Black & Gray (excluding lower arms)

📦 What's Included:

• RX28SE Gen 3 Chassis Kit

• One Set of Wheels & Tires

• Steel Tub Chassis

• Ball & Gear Differential

• Black & Gray Plastic Parts (excluding lower arms)

⚠️ Note: Electronics, body, and mounting hardware are NOT included.

📏 Specifications:

• Wheelbase: 98mm

• Weight (RTR): 145g–170g (depending on body & electronics)

• Rear Track Width: 69mm–78mm

• Front Track Width: 72mm–75mm

🔌 Required to Complete (Not Included):

• Body & Mounting Hardware

• Electronics:

  • Motor

  • LiPo Battery

  • ESC (Electronic Speed Controller)

  • Receiver

  • Servo

✅ Servo Compatibility:

• Reflex Racing RRE007 (20T Spline) – Recommended

• AGFC A06CLS V1

• GL Racing Servo

• PN Anima

• Atomic Servo (tight fit, but correct spline size)

⚠️ Important Notes:

• ELECTRONICS ARE NOT INCLUDED

RX28-045G2 (Black: Medium; Kit w/ 2 Upper & 2 Lower Arms, 4x Balls & 4x Screws)