RX525

RX28A-23

RX28A-17-SS

Softest of the K Version front springs. These are particularly good in high traction conditions when your car is getting tippy. We recommend 1.75mm of ride height 0.2-0.3mm of droop when loaded without body. Closer to 0 droop when running plastic bodies.

RX529

Sturdy, good looking and lightweight, this bumper is perfect to mount to Longer Nose GT Bodies like the Marka RK-W

RX28-051

This is our interpretation of a Racing Body. Developed over the last 6 months to provide more stability, downforce and steering so that your 1/28 scale car car run faster, more consistent laps. The smooth design of the front pontoons helps the body slide off of walls, preventing hang ups on RCP Track.

This listing has only the body. We recommend using our GT Bumper (RX520)

RX28-049

These Gen 2 side links are stronger and smoother than the original Delrin items. Compatible with all RX28 Kits.

RX28A-18

RX605-40

All new from Reflex Racing is our brand new Low Profile slick tires for RCP tracks. These tires are made from a very tough and long lasting grippy rubber. They were developed to match the grip envelope of our 30 degree radials.

We recommend to mount the tires 1 of 2 ways:

For a less hassle, no truing method, mount on a Reflex Racing Speed Dish Wheel with a 22.6 plate. Let the tire break in over time. It is very long lasting, but the results are that the tire works after a couple of laps. If it is too aggressive in the middle of the corner, try removing some camber or running a softer front spring.

If you like to true your tires, mount them up on a truer and bring them down to 22.7-22.8mm and use with a 22.6 plate. After truing, the tires may be a little bit aggressive while they break in, so make sure you have some freshly skimmed 30 degree rear radials or you may have too much front bite. Since the material is very hard, we recommend running the tire truer where the tire and drum are spinning away from each other. With the PN Brand of truers, we find the most success running the truer in reverse and around 6v.

So when do you chose the 45 vs the 40? The 40 cuts a little bit harder, but it is smoother in the middle of the corner. Opposite is true for the 45. It really depends on what you are trying to do. If you want more middle and exit, use the 45. If you want smoother middle and exit, use the 40.

***Wheels are for picture only, they are not included***

RX28-041

4 pcs M1.2x3 and 4 pcs M1.2x4

RX28A-30

Go longer between re-builds with these dust covers for your ball diff. Compatible only with the Reflex Racing V3 Spurs and beyond, these dust covers should work on the majority of diffs out there when using a Version 3 and beyond ball diff spur.

The covers add about 1.6g of weight to your diff.

RX28A-36

These springs are in the same dimensions as the RX28 Double A Arm Front Springs. They are stiffer than the Gold springs and are good for Lower Roll Center Set Ups (when removing shims under the knuckle). These springs are also meant to be used in the rear of your Giulia Conversion kit from Reflex Racing.

The order of stiffness from less to most is :     GOLD>>>ORANGE>>>BLUE>>>RED

RX28A-26

Linear springs are smoother in response than the standard springs. They are wound from smaller diameter wire and have less coils. This allows for the spring to have a more linear response through the suspension stroke. The front end tends to have a more constant response instead of getting more aggressive as the car rolls deeper; which is the case with the standard type springs. The Green Springs are similar in rate to the Kit Gold Springs (RX28A-12).

RX533

Sturdy, good looking and lightweight, this bumper is perfect to mount the Rad Body Ocho Pan Car body. Compatible with our RX53Weight Balance Set.

RX28K-UKIT

Updated kit to bring your RX28K Gen 1 car to Gen 2 spec.

This kit includes all the critical update parts included in the new Generation cars. It includes:

-RX28A-20 Reflex Racing RX28 30g Steel Chassis Plate and SE Style steering CF plate

-RX28-052 RX28 Gen 2 Motor Mount

-RX28-050 RX28 Gen 2 Molded Center Pivot

-RX28-049 RX28 Gen 2 Molded Side Links

Gen 3 springs.  They are shorter than previous side springs, but are compatible across platforms.

RX514V2

All New for Reflex is the GL Racing GLR 514V2 Stainless Steel Chassis. More forward weight bias for better stability and less traction rolling. Black slick coating and chamfered edges for less friction on the track when bottoming out and rolling on RCP.

This V2 Chassis is made from Coated Stainless Steel, which is stiffer than brass and in turn makes the car stay flatter and traction roll less. It is also much tougher and is almost impossible to bend, so your car should run completely tweak free!

MTS10001

SET YOUR TWEAK WITH THE MINI-Z TWEAK STATION!

USER GUIDE: https://minitweakstation.com/wp-content/uploads/2023/04/Mini-Tweak-Station-User-Guide.pdf